LibraryMAE-MT-01 · Rev. 1 · November 2026
Materials and composites
Elastic constants, typical properties, lamination theory, fatigue, fracture and corrosion
Stress, strain and elastic constants
| Quantity | Relation | Notes |
|---|---|---|
| Normal stress and strain | σ = F/A ; ε = ΔL/L₀ | |
| Hooke’s law | σ = E ε ; τ = G γ | linear elastic range |
| Poisson’s ratio | ν = −εlat / εaxial | about 0.33 for aluminium and titanium alloys |
| Isotropic relation | G = E / [2(1 + ν)] | |
| Thermal strain | εT = α ΔT | restrained: σ = −E α ΔT |
| Specific stiffness and strength | E/ρ ; σu/ρ | the figures of merit for light structures |
Typical room-temperature properties
| Material | E (GPa) | ρ (g/cm³) | σu / σy (MPa) | Typical use |
|---|---|---|---|---|
| 2024-T3 aluminium | 73.1 | 2.78 | 483 / 345 | fuselage skin, damage tolerant |
| 7075-T6 aluminium | 71.7 | 2.81 | 572 / 503 | highly loaded fittings, upper wing |
| Ti-6Al-4V (annealed) | 113.8 | 4.43 | 950 / 880 | engine and high-temperature structure |
| Inconel 718 (aged) | 200 | 8.19 | ≈1375 / ≈1100 | turbine discs and casings |
| Carbon/epoxy UD, fibre direction | 181 | 1.60 | 1500 (tension) | E₂ = 10.3 GPa, G₁₂ = 7.17 GPa |
| Glass/epoxy UD, fibre direction | 38.6 | 1.80 | 1062 (tension) | E₂ = 8.27 GPa, G₁₂ = 4.14 GPa |
Handbook typical values for orientation only. Design uses statistically based allowables (MMPDS A- and B-basis, CMH-17) for the specific form, thickness and temper.
Composites: micromechanics and laminates
| Quantity | Relation | Notes |
|---|---|---|
| Rule of mixtures, fibre direction | E₁ = EfVf + EmVm | Vf + Vm = 1 (no voids) |
| Transverse modulus (inverse rule) | 1/E₂ = Vf/Ef + Vm/Em | lower-bound estimate |
| Major Poisson’s ratio | ν₁₂ = νfVf + νmVm | |
| Lamina density | ρ = ρfVf + ρmVm | |
| Reciprocity | ν₁₂/E₁ = ν₂₁/E₂ | |
| Laminate constitutive law | {N ; M} = [A B ; B D] {ε⁰ ; κ} | classical lamination theory |
| Stiffness matrices | Aij = Σ Q̄ij(zk − zk−1) ; Bij = ½ Σ Q̄ij(zk² − zk−1²) ; Dij = ⅓ Σ Q̄ij(zk³ − zk−1³) | sum over plies k |
| Stacking notation | [0/±45/90]s | symmetric: B = 0, no bending–extension coupling |
| Quasi-isotropic layup | equal plies at 0, ±45 and 90° (or 0, ±60°) | in-plane stiffness independent of direction |
Fatigue and fracture
| Quantity | Relation | Notes |
|---|---|---|
| Stress ratio and amplitude | R = σmin/σmax ; σa = (σmax − σmin)/2 | R = −1 fully reversed |
| Basquin (S–N) relation | σa = σ′f (2Nf)b | b typically −0.05 to −0.12 |
| Goodman mean-stress line | σa/Se + σm/Su = 1 | |
| Palmgren–Miner rule | Σ ni/Ni = 1 at failure | linear damage accumulation |
| Stress intensity factor | K = Y σ √(πa) | Y: geometry factor, a: crack length |
| Fast fracture | K = KIc | plane-strain fracture toughness |
| Paris crack-growth law | da/dN = C (ΔK)m | basis of damage-tolerance inspection intervals |
Fracture toughness (Callister)
| Material | σy (MPa) | KIc (MPa√m) |
|---|---|---|
| 7075-T651 aluminium | 495 | 24 |
| 4340 steel, tempered at 260 °C | 1640 | 50 |
| Ti-6Al-4V | 910 | 44–66 |
Corrosion in aircraft
| Type | Mechanism | Where it is found |
|---|---|---|
| Galvanic | two dissimilar metals in an electrolyte | anodic metal corrodes; magnesium, zinc, cadmium and aluminium are anodic to steel, stainless steel, titanium and carbon fibre |
| Pitting | localised breakdown of the passive film | common on aluminium and stainless steel |
| Intergranular and exfoliation | attack along grain boundaries; layers lift in rolled or extruded parts | high-strength aluminium alloys |
| Stress corrosion cracking | sustained tensile stress plus corrosive environment | fittings, forgings, interference-fit fasteners |
| Fretting | small relative motion between loaded surfaces | joints, bearings, splines |
| Filiform | thread-like attack under paint films | starts where humidity is high and the primer is poor |
Sources
- Callister, W. D. and Rethwisch, D. G., Materials Science and Engineering: An Introduction, 10th ed., Wiley, 2018 (fracture toughness table).
- ASM International, ASM Handbook, Vol. 2 (non-ferrous alloys); typical properties of 2024-T3, 7075-T6, Ti-6Al-4V and Inconel 718.
- Kaw, A. K., Mechanics of Composite Materials, 2nd ed., CRC Press, 2006 (unidirectional lamina properties, lamination theory).
- Battelle, Metallic Materials Properties Development and Standardization (MMPDS); Composite Materials Handbook CMH-17 (design allowables).
- FAA, Aviation Maintenance Technician Handbook — General, FAA-H-8083-30B, 2023, Chapter 6 (corrosion).
Study material only. Not approved maintenance or operational data; always use the current approved documentation.