LibraryMAE-SY-01 · Rev. 1 · November 2026
Aircraft systems
Hydraulic, pneumatic, pressurisation, fuel, electrical and other airframe systems
Hydraulic power
| Item | Relation or value | Notes |
|---|---|---|
| Pascal’s principle | p = F/A ; F₂ = F₁ A₂/A₁ | force multiplication by area ratio |
| Actuator force and speed | F = p A ; v = Q/A | Q: volumetric flow |
| Hydraulic power | P = p Q | |
| System pressure | 3000 psi (20.7 MPa) on most transport aircraft; 5000 psi (34.5 MPa) on A380 and 787 | higher pressure, smaller lines and actuators |
| Fluids | MIL-PRF-5606 (mineral oil, red); MIL-PRF-83282 (synthetic, fire resistant); phosphate ester (Type IV/V) on transport aircraft | never mix fluids or seals |
| Main components | reservoir, engine-driven pump, electric pump, accumulator, priority valve, filters, power transfer unit, ram air turbine |
Pneumatic, air conditioning and pressurisation
| Item | Description | Notes |
|---|---|---|
| Bleed air | tapped from engine and APU compressors, regulated and cooled in a precooler | used for air conditioning, pressurisation, wing anti-ice and engine start |
| Air cycle machine | compressor, heat exchangers and expansion turbine cool the supply air | packs |
| Pressure differential | Δp = pcabin − pambient | sets fuselage hoop stress σ = Δp r / t |
| Cabin altitude limit | not more than 8000 ft at the maximum operating altitude in normal operation | 14 CFR 25.841 |
| Bleedless architecture | electric compressors supply cabin air (Boeing 787) |
Fuel
| Item | Value or description | Notes |
|---|---|---|
| Jet A-1 | freezing point at most −47 °C | ASTM D1655 / DEF STAN 91-091 |
| Jet A | freezing point at most −40 °C | ASTM D1655 |
| Jet fuel density at 15 °C | 775–840 kg/m³ | fuel is loaded by mass, metered by volume |
| Avgas 100LL | blue dye; leaded aviation gasoline for piston engines | ASTM D910 |
| System elements | tanks and surge tanks, boost pumps, crossfeed, vent, jettison, quantity gauging (capacitance probes) | |
| Hazards | water, microbial growth, fuel icing, static discharge during refuelling | sump drains, bonding |
Electrical power
| Item | Description | Notes |
|---|---|---|
| Conventional AC | 115/200 V, 400 Hz, three-phase, constant frequency (IDG) | integrated drive generator |
| Variable frequency AC | frequency follows engine speed (about 360–800 Hz) | A380; 787 uses 235 V AC |
| DC | 28 V DC from transformer–rectifier units and batteries | 787 also ±270 V DC |
| Emergency sources | battery, static inverter, ram air turbine generator | |
| Power relation | P = V I cos φ ; three-phase P = √3 VL IL cos φ | cos φ: power factor |
Other systems
| System | Description | Notes |
|---|---|---|
| Ice and rain protection | hot bleed air, electrothermal mats, pneumatic de-ice boots, fluid (freezing point depressant) systems, rain repellent and wipers | |
| Fire protection | continuous-loop or pneumatic detectors; Halon 1301 bottles fired into engine nacelles and APU | two-shot systems on engines |
| Landing gear | oleo-pneumatic shock struts, retraction actuators, steering, carbon or steel brakes, antiskid | |
| Flight controls | mechanical, hydromechanical, fly-by-wire with flight control computers | redundant hydraulic or electric actuation |
| Oxygen | crew gaseous oxygen; passenger chemical generators or gaseous systems | drop-out masks above a set cabin altitude |
Sources
- Moir, I. and Seabridge, A., Aircraft Systems: Mechanical, Electrical and Avionics Subsystems Integration, 3rd ed., Wiley, 2008.
- FAA, Aviation Maintenance Technician Handbook — Airframe, FAA-H-8083-31B, 2023.
- 14 CFR § 25.841, Pressurized cabins.
- ASTM D1655, Standard Specification for Aviation Turbine Fuels; ASTM D910, Standard Specification for Leaded Aviation Gasolines.
Study material only. Not approved maintenance or operational data; always use the current approved documentation.