Aircraft conceptual design

LibraryMAE-DS-01 · Rev. 1 · November 2026

Aircraft conceptual design

Wing geometry, weight estimation, drag polar, sizing constraints and tail volumes

Wing geometry

QuantityRelationNotes
Aspect ratioAR = b²/S
Taper ratioλ = ct/cr
Mean aerodynamic chord (trapezoidal wing)c̄ = (2/3) cr (1 + λ + λ²)/(1 + λ)
Spanwise position of c̄ȳ = (b/6)(1 + 2λ)/(1 + λ)
Oswald factor estimate, straight winge = 1.78 (1 − 0.045 AR0.68) − 0.64Raymer

Weight estimation

QuantityRelationNotes
Take-off weight build-upW₀ = (Wcrew + Wpayload) / [1 − Wf/W₀ − We/W₀]solved by iteration
Fuel fractionWf/W₀ = 1.06 (1 − Wx/W₀)6 % reserve and trapped fuel
Mission segment fractionswarm-up and take-off 0.970 ; climb 0.985 ; landing 0.995historical (Raymer)
Cruise segmentWi/Wi−1 = exp[−R c / (V (L/D))]from Breguet
Loiter segmentWi/Wi−1 = exp[−E c / (L/D)]

Drag polar and range

QuantityRelationNotes
Parabolic drag polarCD = CD0 + K CL² ; K = 1/(π AR e)
Maximum lift-to-drag ratio(L/D)max = 1 / (2√(CD0K)) at CL = √(CD0/K)
Breguet range, jetR = (V/c)(L/D) ln(Wi/Wf)c: thrust-specific fuel consumption
Breguet range, propellerR = (ηp/c)(L/D) ln(Wi/Wf)c: power-specific fuel consumption
Endurance, jetE = (1/c)(L/D) ln(Wi/Wf)

Sizing: wing loading and thrust-to-weight

QuantityRelationNotes
StallW/S = ½ ρ Vs² CL,maxupper limit on wing loading
ClimbT/W = 1/(L/D) + GG: climb gradient
CruiseT/W = q CD0/(W/S) + (W/S)/(q π AR e)q: dynamic pressure
Sustained turnT/W = q CD0/(W/S) + n²(W/S)/(q π AR e)n: load factor
Constraint diagramall requirements plotted as T/W against W/Sdesign point in the feasible region

Tail volume coefficients (Raymer, typical)

Aircraft typeHorizontal cHT = LHTSHT/(c̄S)Vertical cVT = LVTSVT/(bS)
Sailplane0.500.02
General aviation, single engine0.700.04
Jet fighter0.400.07
Jet transport1.000.09

Design phases

PhaseContentNotes
Conceptualrequirements, configuration, sizing, trade studiesmany options, coarse methods
Preliminaryfrozen configuration, wind-tunnel testing, structural and systems layout
Detailparts, tooling, manufacturing drawings, certification analysis

Sources

  1. Raymer, D. P., Aircraft Design: A Conceptual Approach, 6th ed., AIAA, 2018.
  2. Anderson, J. D., Aircraft Performance and Design, McGraw-Hill, 1999.
  3. Roskam, J., Airplane Design, Parts I–VIII, DARcorporation.

Study material only. Not approved maintenance or operational data; always use the current approved documentation.

Mr Aircraft Engineer — open aviation and aerospace education.Study material only; not approved maintenance data.About · Contact · Privacy · Terms