LibraryMAE-MX-01 · Rev. 1 · November 2026
Maintenance, inspection and NDT
Maintenance concepts, MSG-3 inspections, NDT methods and relations, ATA chapters
Maintenance philosophy
| Concept | Meaning | Notes |
|---|---|---|
| Hard time | part removed at a fixed life (hours, cycles or calendar) | life-limited parts, e.g. engine discs |
| On condition | part kept in service while periodic inspection shows it serviceable | |
| Condition monitoring | no scheduled task; failures and trends are tracked | items without safety effect |
| MSG-3 task types | lubrication/servicing, operational or visual check, inspection or functional check, restoration, discard | task-oriented programme |
| MSG-3 structural inspections | general visual (GVI), detailed (DET), special detailed (SDI) | SDI uses NDT or special access |
| Damage tolerance | cracks are found by inspection before they reach critical length | inspection interval from crack-growth analysis |
Non-destructive testing methods
| Method | Detects | Notes |
|---|---|---|
| Visual and borescope | surface damage, corrosion, internal engine parts | first and most used method |
| Liquid penetrant (PT) | surface-breaking cracks in non-porous material | clean, apply, dwell, remove, develop |
| Magnetic particle (MT) | surface and near-surface cracks in ferromagnetic material | crack must lie across the field; demagnetise afterwards |
| Eddy current (ET) | surface and near-surface cracks, corrosion thinning, conductivity, coating thickness | conductive materials, bolt holes, multilayer joints |
| Ultrasonic (UT) | internal flaws, thickness, delaminations and disbonds | pulse-echo, through-transmission, phased array |
| Radiography (RT) | internal volumetric defects, water in honeycomb | film, digital or computed; radiation safety |
| Thermography and tap test | disbonds and delaminations in composites and bonded parts |
NDT relations
| Quantity | Relation | Notes |
|---|---|---|
| Eddy current standard depth | δ = 1 / √(π f μ σ) | lower frequency, deeper penetration |
| Wave relation | v = f λ | |
| Pulse-echo depth | d = v t / 2 | t: round-trip time |
| Acoustic impedance | Z = ρ v | |
| Reflected energy at an interface | R = [(Z₂ − Z₁)/(Z₂ + Z₁)]² | near total at metal–air interfaces, hence couplant |
| Longitudinal / shear velocity, aluminium | ≈ 6320 / 3130 m/s | |
| Longitudinal / shear velocity, steel | ≈ 5920 / 3240 m/s |
ATA iSpec 2200 chapters often used
| 05 Time limits / maintenance checks | 12 Servicing | 20 Standard practices — airframe |
| 21 Air conditioning | 24 Electrical power | 27 Flight controls |
| 28 Fuel | 29 Hydraulic power | 30 Ice and rain protection |
| 32 Landing gear | 36 Pneumatic | 49 Airborne auxiliary power |
| 51 Standard practices — structures | 57 Wings | 72 Engine |
Personnel and documentation
| Item | Description | Notes |
|---|---|---|
| NDT personnel | EN 4179 / NAS 410 levels 1, 2 and 3 | employer-based certification |
| Approved data | AMM, SRM, CMM, IPC, NDT manual, airworthiness directives, service bulletins | always the current revision |
| Acceptable data where none exist | FAA AC 43.13-1B for minor repairs on non-pressurised areas | |
| Release | certificate of release to service by appropriately licensed or authorised staff | EASA Part-145, Part-66 |
Sources
- Airlines for America, ATA MSG-3: Operator/Manufacturer Scheduled Maintenance Development.
- FAA, Aviation Maintenance Technician Handbook — General, FAA-H-8083-30B, 2023 (inspection and NDI).
- FAA, AC 43.13-1B, Acceptable Methods, Techniques, and Practices — Aircraft Inspection and Repair, Chapter 5.
- Hellier, C. J., Handbook of Nondestructive Evaluation, 2nd ed., McGraw-Hill, 2012.
- EN 4179, Aerospace series — Qualification and approval of personnel for non-destructive testing.
Study material only. Not approved maintenance or operational data; always use the current approved documentation.